Home Home > GIT Browse
summaryrefslogtreecommitdiff
blob: 7478f03ccbae2dd582800c1a5b823271e5cfb842 (plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
246
247
248
249
250
251
// SPDX-License-Identifier: GPL-2.0-only
/*
 * Core driver for STw4810/STw4811
 *
 * Copyright (C) 2013 ST-Ericsson SA
 * Written on behalf of Linaro for ST-Ericsson
 *
 * Author: Linus Walleij <linus.walleij@linaro.org>
 */

#include <linux/err.h>
#include <linux/i2c.h>
#include <linux/init.h>
#include <linux/mfd/core.h>
#include <linux/mfd/stw481x.h>
#include <linux/module.h>
#include <linux/regmap.h>
#include <linux/spinlock.h>
#include <linux/slab.h>

/*
 * This driver can only access the non-USB portions of STw4811, the register
 * range 0x00-0x10 dealing with USB is bound to the two special I2C pins used
 * for USB control.
 */

/* Registers inside the power control address space */
#define STW_PC_VCORE_SEL	0x05U
#define STW_PC_VAUX_SEL		0x06U
#define STW_PC_VPLL_SEL		0x07U

/**
 * stw481x_get_pctl_reg() - get a power control register
 * @stw481x: handle to the stw481x chip
 * @reg: power control register to fetch
 *
 * The power control registers is a set of one-time-programmable registers
 * in its own register space, accessed by writing addess bits to these
 * two registers: bits 7,6,5 of PCTL_REG_LO corresponds to the 3 LSBs of
 * the address and bits 8,9 of PCTL_REG_HI corresponds to the 2 MSBs of
 * the address, forming an address space of 5 bits, i.e. 32 registers
 * 0x00 ... 0x1f can be obtained.
 */
static int stw481x_get_pctl_reg(struct stw481x *stw481x, u8 reg)
{
	u8 msb = (reg >> 3) & 0x03;
	u8 lsb = (reg << 5) & 0xe0;
	unsigned int val;
	u8 vrfy;
	int ret;

	ret = regmap_write(stw481x->map, STW_PCTL_REG_HI, msb);
	if (ret)
		return ret;
	ret = regmap_write(stw481x->map, STW_PCTL_REG_LO, lsb);
	if (ret)
		return ret;
	ret = regmap_read(stw481x->map, STW_PCTL_REG_HI, &val);
	if (ret)
		return ret;
	vrfy = (val & 0x03) << 3;
	ret = regmap_read(stw481x->map, STW_PCTL_REG_LO, &val);
	if (ret)
		return ret;
	vrfy |= ((val >> 5) & 0x07);
	if (vrfy != reg)
		return -EIO;
	return (val >> 1) & 0x0f;
}

static int stw481x_startup(struct stw481x *stw481x)
{
	/* Voltages multiplied by 100 */
	static const u8 vcore_val[] = {
		100, 105, 110, 115, 120, 122, 124, 126, 128,
		130, 132, 134, 136, 138, 140, 145
	};
	static const u8 vpll_val[] = { 105, 120, 130, 180 };
	static const u8 vaux_val[] = { 15, 18, 25, 28 };
	u8 vcore;
	u8 vcore_slp;
	u8 vpll;
	u8 vaux;
	bool vaux_en;
	bool it_warn;
	int ret;
	unsigned int val;

	ret = regmap_read(stw481x->map, STW_CONF1, &val);
	if (ret)
		return ret;
	vaux_en = !!(val & STW_CONF1_PDN_VAUX);
	it_warn = !!(val & STW_CONF1_IT_WARN);

	dev_info(&stw481x->client->dev, "voltages %s\n",
		(val & STW_CONF1_V_MONITORING) ? "OK" : "LOW");
	dev_info(&stw481x->client->dev, "MMC level shifter %s\n",
		(val & STW_CONF1_MMC_LS_STATUS) ? "high impedance" : "ON");
	dev_info(&stw481x->client->dev, "VMMC: %s\n",
		(val & STW_CONF1_PDN_VMMC) ? "ON" : "disabled");

	dev_info(&stw481x->client->dev, "STw481x power control registers:\n");

	ret = stw481x_get_pctl_reg(stw481x, STW_PC_VCORE_SEL);
	if (ret < 0)
		return ret;
	vcore = ret & 0x0f;

	ret = stw481x_get_pctl_reg(stw481x, STW_PC_VAUX_SEL);
	if (ret < 0)
		return ret;
	vaux = (ret >> 2) & 3;
	vpll = (ret >> 4) & 1; /* Save bit 4 */

	ret = stw481x_get_pctl_reg(stw481x, STW_PC_VPLL_SEL);
	if (ret < 0)
		return ret;
	vpll |= (ret >> 1) & 2;

	dev_info(&stw481x->client->dev, "VCORE: %u.%uV %s\n",
		vcore_val[vcore] / 100, vcore_val[vcore] % 100,
		(ret & 4) ? "ON" : "OFF");

	dev_info(&stw481x->client->dev, "VPLL:  %u.%uV %s\n",
		vpll_val[vpll] / 100, vpll_val[vpll] % 100,
		(ret & 0x10) ? "ON" : "OFF");

	dev_info(&stw481x->client->dev, "VAUX:  %u.%uV %s\n",
		vaux_val[vaux] / 10, vaux_val[vaux] % 10,
		vaux_en ? "ON" : "OFF");

	ret = regmap_read(stw481x->map, STW_CONF2, &val);
	if (ret)
		return ret;

	dev_info(&stw481x->client->dev, "TWARN: %s threshold, %s\n",
		it_warn ? "below" : "above",
		(val & STW_CONF2_MASK_TWARN) ?
		 "enabled" : "mask through VDDOK");
	dev_info(&stw481x->client->dev, "VMMC: %s\n",
		(val & STW_CONF2_VMMC_EXT) ? "internal" : "external");
	dev_info(&stw481x->client->dev, "IT WAKE UP: %s\n",
		(val & STW_CONF2_MASK_IT_WAKE_UP) ? "enabled" : "masked");
	dev_info(&stw481x->client->dev, "GPO1: %s\n",
		(val & STW_CONF2_GPO1) ? "low" : "high impedance");
	dev_info(&stw481x->client->dev, "GPO2: %s\n",
		(val & STW_CONF2_GPO2) ? "low" : "high impedance");

	ret = regmap_read(stw481x->map, STW_VCORE_SLEEP, &val);
	if (ret)
		return ret;
	vcore_slp = val & 0x0f;
	dev_info(&stw481x->client->dev, "VCORE SLEEP: %u.%uV\n",
		vcore_val[vcore_slp] / 100, vcore_val[vcore_slp] % 100);

	return 0;
}

/*
 * MFD cells - we have one cell which is selected operation
 * mode, and we always have a GPIO cell.
 */
static struct mfd_cell stw481x_cells[] = {
	{
		.of_compatible = "st,stw481x-vmmc",
		.name = "stw481x-vmmc-regulator",
		.id = -1,
	},
};

static const struct regmap_config stw481x_regmap_config = {
	.reg_bits = 8,
	.val_bits = 8,
};

static int stw481x_probe(struct i2c_client *client,
			 const struct i2c_device_id *id)
{
	struct stw481x			*stw481x;
	int ret;
	int i;

	stw481x = devm_kzalloc(&client->dev, sizeof(*stw481x), GFP_KERNEL);
	if (!stw481x)
		return -ENOMEM;

	i2c_set_clientdata(client, stw481x);
	stw481x->client = client;
	stw481x->map = devm_regmap_init_i2c(client, &stw481x_regmap_config);
	if (IS_ERR(stw481x->map)) {
		ret = PTR_ERR(stw481x->map);
		dev_err(&client->dev, "Failed to allocate register map: %d\n",
			ret);
		return ret;
	}

	ret = stw481x_startup(stw481x);
	if (ret) {
		dev_err(&client->dev, "chip initialization failed\n");
		return ret;
	}

	/* Set up and register the platform devices. */
	for (i = 0; i < ARRAY_SIZE(stw481x_cells); i++) {
		/* One state holder for all drivers, this is simple */
		stw481x_cells[i].platform_data = stw481x;
		stw481x_cells[i].pdata_size = sizeof(*stw481x);
	}

	ret = devm_mfd_add_devices(&client->dev, 0, stw481x_cells,
				   ARRAY_SIZE(stw481x_cells), NULL, 0, NULL);
	if (ret)
		return ret;

	dev_info(&client->dev, "initialized STw481x device\n");

	return ret;
}

/*
 * This ID table is completely unused, as this is a pure
 * device-tree probed driver, but it has to be here due to
 * the structure of the I2C core.
 */
static const struct i2c_device_id stw481x_id[] = {
	{ "stw481x", 0 },
	{ },
};
MODULE_DEVICE_TABLE(i2c, stw481x_id);

static const struct of_device_id stw481x_match[] = {
	{ .compatible = "st,stw4810", },
	{ .compatible = "st,stw4811", },
	{ },
};
MODULE_DEVICE_TABLE(of, stw481x_match);

static struct i2c_driver stw481x_driver = {
	.driver = {
		.name	= "stw481x",
		.of_match_table = stw481x_match,
	},
	.probe		= stw481x_probe,
	.id_table	= stw481x_id,
};

module_i2c_driver(stw481x_driver);

MODULE_AUTHOR("Linus Walleij");
MODULE_DESCRIPTION("STw481x PMIC driver");
MODULE_LICENSE("GPL v2");